July 13, 2021

The manual is embedded in the build instructions for the various Align kits. This appears to come out of the manual. At least its identical to. i have just ordered an Align 3gx flybarless control unit but i can’t find any instructions online anywhere as i like to usually download and print. Align 3Gx flybarless setup problem Electric Heli Talk. Registered User Without the 3Gx module in place, with servos connected directly to.

Author: Nejinn Tehn
Country: Croatia
Language: English (Spanish)
Genre: Finance
Published (Last): 27 February 2015
Pages: 476
PDF File Size: 2.39 Mb
ePub File Size: 3.21 Mb
ISBN: 295-2-80328-744-6
Downloads: 30935
Price: Free* [*Free Regsitration Required]
Uploader: Gardajinn

If needed, servo reverse is done from the transmitter’s REV reverse function. Originally Posted by Tulo What software?? Adjust the maximum collective pitch using the transmitter’s swashplate mixing function pitch swash AFR. Adjust the servo neutral point and main blade pitch. Power on Futaba 10C 5. This is clearly noticeable in stable hover as well as highly aerobatic routines.

3GX manual – HeliFreak

Why does that manual start on page 20? Cool, I appreciate the help!

With all channels stationary, move the transmitter elevator stick forward, and then back to center position. You need to pick servo type before even connecting the servos aligh you have the potential to damage them.

The control unit will determine the CCPM mixing ratio or traditional mechanical mixing maximum elevator endpoints. I realise I’m going to probably have to modify the throttle curves and pitch curves later for thebut at least it’s a starting point.


Maybe our manuals are different: Move the elevator stick to adjust collective pitch acceleration rate. At least its identical to my manual that starts on page For tail pitch adjustment, center the rudder servo by either setting the 3GX flybarless to normal rate mode non-heading lockor press and hold the SET button for 2 seconds.

The good news is if its a Futaba S-bus receiver then it is capable of using s-bus and one wire to control the lot.

3GX Flybarless System – Introduction – Align

Press and hold the SET button while powering up the alkgn. This completes the rudder endpoint limit adjustment for the left side. Eventually there will also be smartphone apps allowing live adjustments to 3GX without powering down. Just leave the servo horns ailgn until your in setup and install them as close to level as poss at mid stick. I have 2 sats, so would I just: Aug 19, Originally Posted by Tulo Cool, I appreciate the help!

If ava ilable, ensure the following functions are disabled in the transmitter: Jul 06, Jul 15, Originally Posted by Tulo.

Originally Posted by 3ddd i just found out the manual for mine was printed wrong,if you are using futaba it shows the yellow wire going to channel 3 and the purple wire 3bx to 6,they are backwards and need to be switched,but i think this only applies to standard futaba channel mapping.


Align 3gx pdf manual

Plug in flight battery 3. Align 3Gx flybarless setup problem. The software is the manual. Custom parameters have been opened up in 3GX to allow pilots to fine tune numerous settings for manula and rudder.

Mahual Quick Reply – Please Wait. I personally would set it up using the newest software on aligns site Version 1. Originally Posted by skizziks Abenn did you set your end points and travel on the 3GX?

If that doesnt work call the vendor. Dual axis plus rudder sensor dramatically improves swashplate and rudder correction precision compared to last generation 3G.

In the next section, for S. Flybarless portion of the setup If ava ilable, ensure the following functions are disabled in the transmitter: Therefore, BEC output capability should be confirmed to handle burst current when setting collective pitch acceleration, otherwise insufficient current supply may result in flight accidents.

Anti-torque To achieve consistent gyro gain on left and right, 3GX has built in anti-torque compensation function.

Posted in Business